Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
They are making a few good annotation on How to Install a Bathtub as a whole in the content in the next paragraphs.
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old tub is readily available, the job can relocate rapidly; if you have to open a wall surface to get rid of the old tub and position the brand-new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and also set in the brand-new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is much better to think about using one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This short article will assist you mount a new bath tub in your washroom if you have currently purchased a brand-new bathtub and do not need to alter the plan of your previous water system pipes.
Your devices and product list ought to make up the following:
Preparing for the Setup
To start with, the supporting structure provided with the bathroom should be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the limited gain access to that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bathtub up until the spirit level reads degree.
To mount taps, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the bath tub and additionally check the overflow outlet and also the normal outlet for leaks.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub must wait till the tub has been used a minimum of once as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Protect the tap in position with the supplier offered backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former type needs to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, bring about problems with wetness and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is advisable to fit the tiles making use of water-resistant or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very fascinated with How to Install a Bathtub Yourself and I'm hoping you liked our article. Sharing is caring. Who knows, you may be doing someone a favor. We enjoy reading our article about Tools You Need to Install a New Bathtub .
Rely on our emergency expertise. Report this page